焙烧温度对Pd-Cu/凹凸棒土CO常温催化氧化性能的影响

王永钊; 程慧敏; 范莉渊; 石晶; 赵永祥

焙烧温度对Pd-Cu/凹凸棒土CO常温催化氧化性能的影响

山西大学化学化工学院精细化学品教育部工程研究中心, 山西太原 030006

基金项目: 国家自然科学基金（21073114）；山西省青年科技研究基金（2010021008-3）。

详细信息

通讯作者:
王永钊，Fax：+86-351-7011688，E-mail：catalyst@sxu.edu.cn; 赵永祥，E-mail：yxzhao@sxu.edu.cn。

中图分类号: O643
计量
- 文章访问数: 976
- HTML全文浏览量: 19
- PDF下载量: 588
- 被引次数: 0
出版历程
- 收稿日期: 2013-11-11
- 修回日期: 2014-01-06
- 刊出日期: 2014-05-30

Effect of calcination temperature on catalytic performance of Pd-Cu/attapulgite clay catalyst for CO oxidation at room temperature

School of Chemistry and Chemical Engineering, Engineering Research Center for Fine Chemicals of Ministry of Education, Shanxi University, Taiyuan 030006, China

摘要

摘要: 以凹凸棒土（APT）作载体，采用等体积浸渍法制备了Pd-Cu/APT催化剂，以CO氧化为探针反应，在连续流动微反装置上，考察了焙烧温度对催化剂CO常温催化氧化性能的影响。通过N₂-物理吸附、XRD、TG、FT-IR和H₂-TPR等手段对催化剂的结构和性质进行了表征。结果表明，随焙烧温度升高，Pd-Cu/APT中载体逐步脱水，进而引起催化剂结构和织构变化，其中，Cu物种由Cu（OH）Cl逐渐向CuO转变，同时，高分散的Pd物种与Cu物种间相互作用先增强后减弱。经300 ℃焙烧的催化剂比表面积大，Cu物种以Cu（OH）Cl形式存在，且具有良好的分散状态，与Pd物种之间产生较强的相互作用，显著提高了其还原性能。在空速6 000 h^-1、CO体积分数0.5%、水蒸气体积分数3.3%的反应条件下，常温可将CO完全转化800 min以上。焙烧温度高于或低于300 ℃均引起CO常温催化氧化性能的下降。
- Pd-Cu/APT /
- 凹凸棒土 /
- 焙烧温度 /
- CO常温催化氧化
Abstract: Using attapulgite clay(APT) as the support, the catalysts Pd-Cu/APT were prepared by wet impregnation method. The effect of calcination temperature on the catalytic performance for CO oxidation at room temperature was investigated in a fixed-bed continuous flow reactor. Structure and property of the catalysts were characterized by N₂-physisorption, XRD, TG, FT-IR and H₂-TPR. The results showed that as the calcination temperature increased, structure and texture of the catalysts changed due to the desorption of water in the support. Cu species changed from Cu(OH)Cl to CuO gradually, while interactions between highly dispersed Pd and Cu species increased firstly and then decreased. The catalyst calcined at 300 ℃ possessed the highest surface area, dispersed Cu(OH)Cl, and strong interaction between Pd and Cu species, which significantly improved the reducibility of the catalyst. At the reaction conditions of CO 0.5%, GHSV 6 000 h^-1, water content 3.3% and room temperature, the catalyst was able to maintain its activity for CO complete oxidation more than 800 min. Calcination temperatures higher or lower than 300 ℃ caused the lower catalytic activity.
- Pd-Cu/APT /
- attapulgite clay /
- calcination temperature /
- CO oxidation at room temperature

HTML全文

参考文献(24)

QI C X, SU H J, GUAN R G, XU X F. An investigation into phosphate-doped Au/alumina for low temperature CO oxidation[J]. J Phys Chem, 2012, 116(33): 17492-17500.

LI L, WANG A Q, QIAO B T, LIN J, HUANG Y Q, WANG X D, ZHANG T. Origin of the high activity of Au/FeO_x for low-temperature CO oxidation: Direct evidence for a redox mechanism[J]. J Catal, 2013, 299: 90-100.

SATSUMA A, OSAKI K, YANAGIHARA M, OHYAMAO J, SHIMIZU K. Activity controlling factors for low-temperature oxidation of CO over supported Pd catalysts[J]. Appl Catal B: Environ, 2013, 132-133: 511-518.

JONES C, TAYLOR S H, BURROWS A, CRUDACE M J, KIELY C J, HUTCHINGS G J. Cobalt promoted copper manganese oxide catalysts for ambient temperature carbon monoxide oxidation[J]. Chem Commun, 2008, 14: 1707-1709.

ZHU H, QIN Z F, SHAN W J, SHEN W J, WANG J G. Low-temperature oxidation of CO over Pd/CeO₂-TiO₂ catalysts with different pretreatments[J]. J Catal, 2005, 233(1): 41-50.

WANG Y Z, ZHAO Y X, GAO C G, LIU D S. Origin of the high activity and stability of Co₃O₄ in low-temperature CO oxidation[J]. Catal Lett, 2008, 125(1/2): 134-138.

XIE X W, LI Y, LIU Z Q, HARUTA M, SHEN W J. Low-temperature oxidation of CO catalysed by Co₃O₄ nanorods[J]. Nature, 2009, 458: 746-749.

LUO M F, MA J M, LU J Q, SONG Y P, WANG Y J. High-surface area CuO-CeO₂ catalysts prepared by a surfactant-templated method for low-temperature CO oxidation[J]. J Catal, 2007, 246(1): 52-59.

SHEN Y X, LU G Z, GUO Y, WANG Y Q. A synthesis of high-efficiency Pd-Cu-Cl_x/Al₂O₃ catalyst for low temperature CO oxidation[J]. Chem Commun, 2010, 46: 8433-8435.

CHOI K I, VANNICE M A. CO oxidation over Pd and Cu catalysts Ⅱ. Unreduced bimetallic PdCl₂-CuCl₂ dispersed on Al₂O₃ or carbon[J]. J Catal, 1991, 127: 489-511.

WANG L, ZHOU Y B, LIU Q F, GUO Y, LU G Z. Effect of surface properties of activated carbon on CO oxidation over supported Wacker-type catalysts[J]. Catal Today, 2010, 153(3/4): 184-188.

FENG Y F, WANG L, ZHANG Y H, GUO Y, GUO Y L, LU G Z. Deactivation mechanism of PdCl₂-CuCl₂/Al₂O₃catalysts for CO oxidation at temperatures[J]. Chin J Catal, 2013, 34(5): 923-931.

SHEN Y X, LU G Z, GUO Y, WANG Y Q, GUO Y L, GONG X Q. Study on the catalytic reaction mechanism of low temperature oxidation of CO over Pd-Cu-Cl_x/Al₂O₃catalyst[J]. Catal Today, 2011, 175(1): 558-567.

RAKITSKAYA T L, KIOSE T A, OLEKSENKO L P, LUTSENKO L V, DLUBOVSKⅡ R M, VOLKOVA V J. Influence of water content in the Pd(Ⅱ)-Cu(Ⅱ) catalyst fixed on acid-modified basalt tuff on its activity in the carbon monoxide oxidation by oxygen[J]. Russ J Appl Chem, 2012, 85(9): 1339-1344.

王永钊, 张卓, 李凤梅, 赵永祥. Pd-Cu/凹凸棒石黏土催化剂催化CO氧化性能[J]. 工业催化, 2011, 11(19): 75-79. (WANG Yong-zhao, ZHANG Zhuo, LI Feng-mei, ZHAO Yong-xiang. Catalytic performance of Pd-Cu/attapulgite clay catalyst for CO oxidation[J]. Industrial Catalysis, 2011, 11(19): 75-79.)

YANG H M, TANG A D, OUYANG J, LI M, MANN S. From natural attapulgite to mesoporous materials: Methodology, characterization and structural evolution[J]. J Phys Chem B, 2010, 114(7): 2390-2398.

YOU J, CHEN F, ZHAO X B, CHEN Z G. Preparation, characterization and catalytic oxidation property of CeO₂/Cu²⁺-attapulgite (ATP) nanocomposites[J]. J Rare Earth, 2010, 28(9): 347-352.

CAO J L, SHAO G S, WANG Y, LIU Y P, YUAN Z Y. CuO catalysts supported on attapulgite clay for low-temperature CO oxidation[J]. Catal Commun, 2008, 9(15): 2555-2559.

陈丰, 李霞章, 陆晓旺, 王健美, 倪超英, 陈志刚. 凹凸棒石/CeO₂复合纳米材料的合成、表征及催化性能[J]. 硅酸盐学报, 2009, 37(1): 52-56. (CHENG Feng, LI Xia-zhang, LU Xiao-wang, WANG Jian-mei, NI Chao-ying, CHEN Zhi-gang. Preparation and characterization of attapulgite/CeO₂nano-composite material and its catalytic performance[J]. Journal of the Chinese Ceramic Society, 2009, 37(1): 52-56.)

徐慧远, 罗靖洁, 严春蓉, 张燕, 尚书勇. 二氧化硅孔结构对CO氧化用担载型纳米金催化剂的影响[J]. 燃料化学学报, 2012, 40(11): 1397-1402. (XU Hui-yuan, LUO Jing-jie, YAN Chun-rong, ZHANG Yan, SHANG Shu-yong. Impact of silica porosity on the catalytic activity of nanosize gold catalyst for CO oxidation[J]. Journal of Fuel Chemistry and Technology, 2012, 40(11): 1397-1402.)

陈天虎, 王健, 庆承松, 彭书传, 宋垠先, 郭燕. 热处理对凹凸棒石结构、形貌和表面性质的影响[J]. 硅酸盐学报, 2006, 34(11): 1406-1410. (CHEN Tian-hu, WANG Jian, QING Cheng-song, PENG Shu-chuan, SONG Yin-xian, GUO Yan. Effect to heat treatment on structure, morphology and surface properties of palygorskite[J]. Journal of the Chinese Ceramic Society, 2006, 34(11): 1406-1410.)

武应全, 解红娟, 寇永利, 谭理, 韩怡卓, 谭猗生. 焙烧温度对K-Cu/Zn/La/ZrO₂催化剂上异丁醇合成的影响[J]. 燃料化学学报, 2013, 41(7): 868-874. (WU Ying-quan, XIE Hong-juan, KOU Yong-li, TAN Li, HAN Yi-zhuo, TAN Yi-sheng. Effect of calcination temperature on performance of K-Cu/Zn/La/ZrO₂ for isobutanol synthesis[J]. Journal of Fuel Chemistry and Technology, 2013, 41(7): 868-874.)

SOARES O S G P, ÓRFÃO J J M, RUIZ-MARÍNEZ J, SILVESTRE-ALBERO J, SEPLVEDA-ESCRIBANO A, PEREIRA M F R. Pd-Cu/AC and Pt-Cu/AC catalysts for nitrate reduction with hydrogen: Influence of calcination and reduction temperatures[J]. Chem Eng J, 2010, 165(1): 578-88.

李娟, 海航, 闫常峰, 胡蓉蓉, 么志伟, 罗伟民, 郭常青, 李文博. 焙烧温度对二甲醚水蒸气重整制氢Cu/ZnO/Al₂O₃/Cr₂O₃+H-ZSM-5双功能催化剂性能的影响[J]. 燃料化学学报, 2012, 40(10): 1240-1245. (LI Juan, HAI Hang, YAN Chang-feng, HU Rong-rong, YAO Zhi-wei, LUO Wei-min, GUO Chang-qing, LI Wen-bo. Effect of calcination temperature on properties of Cu/ZnO/Al₂O₃/Cr₂O₃+H-ZSM-5 bi-functional catalysts for steam reforming of dimethyl ether[J]. Journal of Fuel Chemistry and Technology, 2012, 40(10): 1240-1245.)

施引文献

资源附件(0)

访问统计

点击查看大图

计量

文章访问数: 976
HTML全文浏览量: 19
PDF下载量: 588
被引次数: 0

姓名
邮箱
手机号码
标题
留言内容
验证码

留言板

焙烧温度对Pd-Cu/凹凸棒土CO常温催化氧化性能的影响

通讯作者:
王永钊，Fax：+86-351-7011688，E-mail：catalyst@sxu.edu.cn; 赵永祥，E-mail：yxzhao@sxu.edu.cn。

计量

Effect of calcination temperature on catalytic performance of Pd-Cu/attapulgite clay catalyst for CO oxidation at room temperature

计量

目录

2023年《燃料化学学报（中英文）》评优结果公布！

留言板

焙烧温度对Pd-Cu/凹凸棒土CO常温催化氧化性能的影响

通讯作者: 王永钊，Fax：+86-351-7011688，E-mail：catalyst@sxu.edu.cn; 赵永祥，E-mail：yxzhao@sxu.edu.cn。

计量

出版历程

Effect of calcination temperature on catalytic performance of Pd-Cu/attapulgite clay catalyst for CO oxidation at room temperature

计量

出版历程

目录

2023年《燃料化学学报（中英文）》评优结果公布！

通讯作者:
王永钊，Fax：+86-351-7011688，E-mail：catalyst@sxu.edu.cn; 赵永祥，E-mail：yxzhao@sxu.edu.cn。