Preparation of B/N co-doped porous carbon sheets and their potassium storage properties
-
摘要: 以甘氨酸为碳源和氮源、硼酸为模板和硼源,采用一步碳化法制备了二维B/N共掺杂多孔碳片(BNCSs)。通过水洗即可除去硼酸模板,合成方法绿色环保。BNCSs上短的孔道缩短了钾离子的传输距离,丰富的微孔提供了大量的储钾活性位点。此外,BNCSs中较高的B/N掺杂量提升了碳基质的缺陷度,扩大了碳层间距,有利于钾离子的吸附、嵌入和脱嵌。钾离子半电池性能的测试结果表明,BNCS800电极展现出高的比容(在0.05 A/g电流密度下为310 mA·h/g)、优异的倍率性能(在2 A/g电流密度下为100 mA·h/g)和良好的循环稳定性(在1 A/g下循环1000次后容量保持率为75.9%)。Abstract: In this paper, two-dimensional B/N co-doped porous carbon sheets (BNCSs) were prepared by one-step carbonization using glycine as carbon source and nitrogen source, boric acid as template and boron source. The boric acid template can be removed by water washing, and the synthesis method is green and environmentally friendly. The short pores in BNCSs shorten the transport distance of potassium ions, and the abundant micropores provide a large number of potassium storage active sites. In addition, the higher B/N doping in BNCSs increases the defect degree of carbon matrix, expands the carbon layer spacing, and is conducive to the adsorption, insertion and de-insertion of potassium ions. The measurement results of potassium ion half cell performance indicate that BNCS800 electrode shows high specific capacity (310 mA·h/g at 0.05 A/g), excellent rate performance (100 mA·h/g at 2 A/g) and good cycle stability (after 1000 cycles at 1 A/g, the capacity retention is 75.9%). This work provides a simple strategy for preparing cathode materials with high capacity and long life.
-
Key words:
- B/N co-doping /
- two-dimensional /
- porous carbon /
- potassium ion battery
-
图 5 NC和BNCSs的全谱图(a);BNCS700(b), BNCS800(c), 和 BNCS900(d)的B 1s谱图;NC(e), BNCS700(f), BNCS800(g)和 BNCS900(h)的N 1s谱图;NC和BNCSs的吡咯氮/吡啶氮比值(i)
Figure 5 XPS survey spectra (a) of NC and BNCSs; B 1s spectra of BNCS700 (b), BNCS800 (c), and BNCS900 (d); N 1s spectra of NC (e), BNCS700 (f), BNCS800 (g) and BNCS900 (h); the ratios of pyrrolic-N/pyridinic-N of NC and BNCSs (i)
表 1 NC和BNCSs样品的孔结构*
Table 1 Pore structural parameters of NC and BNCSs samples
Sample Dap/
nmSBET/
(m2·g−1)Smic/
(m2·g−1)vt/
(cm3·g−1)vmic/
(cm3·g−1)NC 2.07 278 246 0.14 0.13 BNCS700 5.73 492 152 0.70 0.08 BNCS800 5.35 560 216 0.75 0.11 BNCS900 6.58 368 89 0.61 0.05 * Dap: average pore diameter; SBET: specific surface area; Smic: micropore surface area; vt: total pore volume; vmic: micropore volume 表 2 NC和BNCSs中碳、氧、硼、氮元素和含氮官能团的含量
Table 2 Contents of carbon oxygen boron nitrogen elements and nitrogen-containing functional groups in NC and BNCSs
Sample C 1s
/%O 1s
/%B 1s
/%N 1s
/%N 1s functionalities/% pyridinic-N pyrrolic-N graphitic-N N−O NC 83.75 6.46 − 9.79 21 15 56 8 BNCS700 72.43 14.33 1.90 11.34 33 34 31 2 BNCS800 71.95 11.64 4.16 12.25 22 41 32 5 BNCS900 72.18 13.57 3.98 10.27 24 35 30 11 -
[1] WU Y M, ZHAO H T, WU Z G, YUE L C, LIANG J, LIU Q, LUO Y L, GAO S. Y, LU S Y, CHEN G, SHI X F, ZHONG B H, GUO X D, SUN X P. Rational design of carbon materials as anodes for potassium-ion batteries[J]. Energy Storage Mater,2021,34:483−507. doi: 10.1016/j.ensm.2020.10.015 [2] ZHU L F, ZHANG Z, LUO J D, ZHANG H, QU Y H, YANG Z Y. Self-templated synthesis of hollow hierarchical porous olive-like carbon toward universal high-performance alkali (Li, Na, K)-ion storage[J]. Carbon,2021,174:317−324. doi: 10.1016/j.carbon.2020.12.029 [3] ZHANG Q F, CHENG X L, WANG C X, RAO A M, LU B A. Sulfur-assisted large-scale synthesis of graphene microspheres for superior potassium-ion batteries[J]. Energy Environ Sci,2021,14(2):965−974. doi: 10.1039/D0EE03203D [4] WANG B, ZHANG Z Y, YUAN F, ZHANG D, WANG Q J, LI W, LI Z J, WU Y A, WANG W. An insight into the initial coulombic efficiency of carbon-based anode materials for potassium-ion batteries[J]. Chem Eng J,2022,428:131093. doi: 10.1016/j.cej.2021.131093 [5] QIN G H, LIU Y H, LIU F S, XUAN S, HOU L R, LIU B B, YUAN C Z. Magnetic field assisted construction of hollow red P nanospheres confined in hierarchical N-doped carbon nanosheets/nanotubes 3D framework for efficient potassium storage[J]. Adv Energy Mater,2020,11(4):2003429. [6] ZHONG Y L, DAI W X, LIU D, WANG W, WANG L T, XIE J P, LI R, YUAN Q L, HONG G. Nitrogen and fluorine dual doping of soft carbon nanofibers as advanced anode for potassium ion batteries[J]. Small,2021,17(43):2101576. doi: 10.1002/smll.202101576 [7] WU Z R, ZOU J, SHABANIAN S, GOLOVIN K, LIU J. The roles of electrolyte chemistry in hard carbon anode for potassium-ion batteries[J]. Chem Eng J,2022,427:130972. doi: 10.1016/j.cej.2021.130972 [8] RUAN J F, MO F J, CHEN Z L, LIU M, ZHENG S Y, WU R B, FANG F, SONG Y, SUN D L. Rational construction of nitrogen-doped hierarchical dual-carbon for advanced potassium-ion hybrid capacitors[J]. Adv Energy Mater,2020,10(15):1904045. doi: 10.1002/aenm.201904045 [9] LI C, FU Q, ZHAO K J, WANG Y P, TANG H, LI H H, JIANG H B, CHEN L. Nitrogen and phosphorous dual-doped graphene aerogel with rapid capacitive response for sodium-ion batteries[J]. Carbon,2018,139:1117−1125. doi: 10.1016/j.carbon.2018.06.035 [10] WU Y J, SUN Y J, ZHENG J F, RONG J H, LI H Y, NIU L. MXenes: Advanced materials in potassium ion batteries[J]. Chem Eng J,2021,404:126565. doi: 10.1016/j.cej.2020.126565 [11] DENG H L, WANG L, LI S Y, ZHANG M, WANG T, ZHOU J, CHEN M X, CHEN S, CAO J H, ZHANG Q S, ZHU J, LU B A. Radial pores in nitrogen/oxygen dual-doped carbon nanospheres anode boost high-power and ultrastable potassium-ion batteries[J]. Adv Funct Mater,2021,31(51):2107246. doi: 10.1002/adfm.202107246 [12] ZHANG L P, WANG W, LU S F, XIANG Y. Carbon anode materials: A detailed comparison between Na-ion and K-ion batteries[J]. Adv Energy Mater,2021,11(11):2003640. doi: 10.1002/aenm.202003640 [13] JIN Q Z, LI W, WANG K L, LI H M, FENG P Y, ZHANG Z C, WANG W, JIANG K. Tailoring 2D heteroatom-doped carbon nanosheets with dominated pseudocapacitive behaviors enabling fast and high-performance sodium storage[J]. Adv Funct Mater,2020,30(14):1909907. doi: 10.1002/adfm.201909907 [14] ZHANG C C, PAN H G, SUN L X, XU F, OUYANG Y F, ROSEI F. Progress and perspectives of 2D materials as anodes for potassium-ion batteries[J]. Energy Storage Mater,2021,38:354−378. doi: 10.1016/j.ensm.2021.03.007 [15] SHARE K, COHN A P, CARTER R, ROGERS B, PINT C L. Role of nitrogen-doped graphene for improved high-capacity potassium ion battery anodes[J]. ACS Nano,2016,10(10):9738−9744. doi: 10.1021/acsnano.6b05998 [16] JIAN Z L, LUO W, JI X L. Carbon electrodes for K-ion batteries[J]. J Am Chem Soc,2015,137(36):11566−9. doi: 10.1021/jacs.5b06809 [17] LU C, SUN Z T, YU L H, LIAN X Y, YI Y Y, JIE L, LIU Z F, DOU S X, SUN J Y. Enhanced kinetics harvested in heteroatom dual-doped graphitic hollow architectures toward high rate printable potassium-ion batteries[J]. Adv Energy Mater,2020,10(28):2001161. doi: 10.1002/aenm.202001161 [18] ZHANG H F, HE X J, WEI F, DONG S A, XIAN N, QIU J S. Moss-covered rock-like hybrid porous carbons with enhanced electrochemical properties[J]. ACS Sustainable Chem Eng,2020,8(8):3065−3071. doi: 10.1021/acssuschemeng.9b05075 [19] LIU Z M, WANG J, JIA X X, LI W L, ZHANG Q F, FAN L, DING H B, YANG H G, YU X Z, LI X K, LU B A. Graphene armored with a crystal carbon shell for ultrahigh-performance potassium ion batteries and aluminum batteries[J]. ACS Nano,2019,13(9):10631−10642. doi: 10.1021/acsnano.9b04893 [20] HE H N, HUANG D, TANG Y G, WANG Q, JI X B, WANG H Y, GUO Z P. Tuning nitrogen species in three-dimensional porous carbon via phosphorus doping for ultra-fast potassium storage[J]. Nano Energy,2019,57:728−736. doi: 10.1016/j.nanoen.2019.01.009 [21] XU Z Q, WU M Q, CHEN Z, CHEN C, YANG J, FENG T T, PAEK E, MITLIN D. Direct structure-performance comparison of all-carbon potassium and sodium ion capacitors[J]. Adv Sci,2019,6(12):1802272. doi: 10.1002/advs.201802272 [22] YAN J, LI W, FENG P Y, WANG R X, JIANG M, HAN J, CAO S L, WANG K L, JIANG K. Enhanced Na + pseudocapacitance in a P, S co-doped carbon anode arising from the surface modification by sulfur and phosphorus with C-S-P coupling[J]. J Mater Chem A,2020,8(1):422−432. doi: 10.1039/C9TA11594C [23] FENG W T, FENG N Y, LIU W, CUI Y P, CHEN C, DONG T T, LIU S, DENG W Q, WANG H L, JIN Y C. Liquid-state templates for constructing B, N, co-doping porous carbons with a boosting of potassium-ion storage performance[J]. Adv Energy Mater,2021,11:2003215. doi: 10.1002/aenm.202003215 [24] TAO L, YANG Y P, WANG H L, ZHENG H L, HAO Y L, SONG W P, SHI J, HUANG M H, MITLIN D. Sulfur-nitrogen rich carbon as stable high capacity potassium ion battery anode: Performance and storage mechanisms[J]. Energy Storage Mater,2020,27:212−225. doi: 10.1016/j.ensm.2020.02.004 [25] CHANG X Q, MA Y F, YANG M, XING T, TANG L Y, CHEN T T, GUO Q B, ZHU X H, LIU J Z, XIA H. In-situ solid-state growth of N, S codoped carbon nanotubes encapsulating metal sulfides for high-efficient-stable sodium ion storage[J]. Energy Storage Mater,2019,23:358−366. doi: 10.1016/j.ensm.2019.04.039 [26] WANG B, GU L, YUAN F, ZHANG D, SUN H L, WANG J, WANG Q J, HUAN W, LI Z J. Edge-enrich N-doped graphitic carbon: Boosting rate capability and cyclability for potassium ion battery[J]. Chem Eng J,2022,432:134321. doi: 10.1016/j.cej.2021.134321 [27] TZADIKOV J, LEVY N R, ABISDRIS L, COHEN R, WEITMAN M, KAMINKER L, GOLDBOURT A, EIN-ELI Y, SHALOM M. Bottom-up synthesis of advanced carbonaceous anode materials containing sulfur for Na-ion batteries[J]. Adv Funct Mater,2020,30(19):2000592. doi: 10.1002/adfm.202000592 [28] CAO B, ZHANG Q, LIU H, XU B, ZHANG S L, ZHOU T F, MAO J F, PANG W K, GUO Z P, LI A, ZHOU J S, CHEN X H, SONG H H. Graphitic carbon nanocage as a stable and high power anode for potassium-ion batteries[J]. Adv Energy Mater,2018,8(25):1801149. doi: 10.1002/aenm.201801149 [29] SHEN C, YUAN K, TIAN T, BAI M H, WANG J G, LI X F, XIE K Y, FU Q G, WEI B. Q. Flexible sub-micro carbon fiber@CNTs as anodes for potassium-ion batteries[J]. ACS Appl Mater Interfaces,2019,11(5):5015−5021. doi: 10.1021/acsami.8b18834 [30] WU Z R, WANG L P, HUANG J, ZOU J, CHEN S L, CHEN H, JIANG C, GAO P, NIU X B. Loofah-derived carbon as an anode material for potassium ion and lithium ion batteries[J]. Electrochim Acta,2019,306:446−453. doi: 10.1016/j.electacta.2019.03.165 [31] ZENG S F, ZHOU X F, WANG B, FENG Y Z, XU R, ZHANG H B, PENG S M, YU Y. Freestanding CNT-modified graphitic carbon foam as a flexible anode for potassium ion batteries[J]. J Mater Chem A,2019,7(26):15774−15781. doi: 10.1039/C9TA03245B [32] WANG S, LIY Y, MA F T, WU X Z, ZHOU P F, MIAO Z C, GAO P B, ZHUO S P, ZHOU J. Phenolic resin-based carbon microspheres for potassium ion storage[J]. Appl Surface Sci,2020,506:144805. doi: 10.1016/j.apsusc.2019.144805 [33] ZHAO C X, LI H, ZOU Y J, QI Y Y, JIAN Z L, CHEN W. Low-cost carbon materials as anode for high-performance potassium-ion batteries[J]. Mater Lett,2020,262:127147. doi: 10.1016/j.matlet.2019.127147 [34] LIU Q, RAO A M, HAN X, LU B A. Artificial SEI for superhigh-performance K-graphite anode[J]. Adv Sci,2021,8(9):2003639. doi: 10.1002/advs.202003639 [35] WANG S Z, ZHAO H P, LV S Y, JIANG H H, SHAO Y L, WU Y Z, HAO X P, LEI Y. Insight into nickel-cobalt oxysulfide nanowires as advanced anode for sodium-ion capacitors[J]. Adv Energy Mater,2021,11(18):2100408. doi: 10.1002/aenm.202100408 [36] QIAN M M, XU Z F, WANG Z C, WEI B, WANG H, HU S X, LIU L M, GUO L. Realizing few-layer iodinene for high-rate sodium-ion batteries[J]. Adv Mater,2020,32(43):e2004835. doi: 10.1002/adma.202004835 [37] JU Z C, LI P Z, MA G Y, XING Z, ZHUANG Q C, QIAN Y T. Few layer nitrogen-doped graphene with highly reversible potassium storage[J]. Energy Storage Mater,2018,11:38−46. doi: 10.1016/j.ensm.2017.09.009